What should be changed to get into the 9's

[jkstang78]

Hi the mustang I have is former MM & FF xproject car Hooligan Hot Rod. Everything that has been done to the car is donw below. The car went 10.30 @ 133. I want to go 9s with this car. So what should be change to achive this. mustang made 515rwhp & 670 ft lbs of tourqe with mods below. I just change intakes to the Edelbrock RPM II.
car weights about 3400lbs.

pics
http://www.cardomain.com/id/jkstang78 (http://www.cardomain.com/id/jkstang78)


HP performance Stage 2 turbo kit.
HP Streeturbo Kit comes complete with 66mm hybrid turbo, 44mm Tial wastegate, Blow-off valve, 76mm mass air meter, custom-built intercooler, CNC mandrel bent headers, tubing and y-pipe, ceramic coating on all piping and headers, braided oil line, 3-ply silicone couplings, stainless steel t-bolt and v-band clamps and all fitting, bolts, nuts.
347 stroker kit from Summit Racing
Scat nodular iron crank
4340 H-beam rods 5.400-inch length
Clevitte 77 brearings
High volume melling oil pump
60 lbs injectors
Trick Flow specialties forged pistons with 8,5:1 compression
Trick Flow Main girdle
Trick flow cam 220/225 degress and 499/510 lift
Trick Flow Heads
Trick Flow intake
TCI rattler damper
SFI-approved flexplate
Lentech strip terminator AOD with Transbrake and
10 inch 2,200 stall torque converter
electriclockup functions.
Pro 5.0 3.31 rear end gear
31 spline moser axles
31 splin traction-lok
Metco's driveshaft safety loop
Aeromotive Fuel System Competition Kit.
**NEW** changed to a Pro-m Univer mass air
**NEW** Crane HI-6 ignition system
**NEW** MSD Pro-Billet Distributors

[clint walker]

the car seems pretty heavy. I took my back seats out and all of the insulation on the floor. it takes a heat gun and a scraper. I also took off my front sway bar. my car now weighs 3070 lbs and it's a 93 GT. also, might look into taking the passenger seat out too when you race. it may just be enough. I always race with about 2 or 3 gallons in my tank so there's not much weight there

[KJMac]

Hi the mustang I have is former MM & FF xproject car Hooligan Hot Rod. Everything that has been done to the car is donw below. The car went 10.30 @ 133. I want to go 9s with this car. So what should be change to achive this. mustang made 515rwhp & 670 ft lbs of tourqe with mods below. I just change intakes to the Edelbrock RPM II.
car weights about 3400lbs.

pics
http://www.cardomain.com/id/jkstang78 (http://www.cardomain.com/id/jkstang78)


HP performance Stage 2 turbo kit.
HP Streeturbo Kit comes complete with 66mm hybrid turbo, 44mm Tial wastegate, Blow-off valve, 76mm mass air meter, custom-built intercooler, CNC mandrel bent headers, tubing and y-pipe, ceramic coating on all piping and headers, braided oil line, 3-ply silicone couplings, stainless steel t-bolt and v-band clamps and all fitting, bolts, nuts.
347 stroker kit from Summit Racing
Scat nodular iron crank
4340 H-beam rods 5.400-inch length
Clevitte 77 brearings
High volume melling oil pump
60 lbs injectors
Trick Flow specialties forged pistons with 8,5:1 compression
Trick Flow Main girdle
Trick flow cam 220/225 degress and 499/510 lift
Trick Flow Heads
Trick Flow intake
TCI rattler damper
SFI-approved flexplate
Lentech strip terminator AOD with Transbrake and
10 inch 2,200 stall torque converter
electriclockup functions.
Pro 5.0 3.31 rear end gear
31 spline moser axles
31 splin traction-lok
Metco's driveshaft safety loop
Aeromotive Fuel System Competition Kit.
**NEW** changed to a Pro-m Univer mass air
**NEW** Crane HI-6 ignition system
**NEW** MSD Pro-Billet Distributors
That is a nice setup! I didn't think it would go that fast with that mild of a set-up. If you want recommendations??? You could do port work to your heads. Definately a bigger cam; 236 .570 114 LSA Hyd. roller. Anything bigger I would go Mech. roller. 3000 Stall.....Hang on!

[Turbo95Cobra]

if u don't mind me asking, how did u get to pick that car up?

[xlr8a4d]

Dang,I didn't even know they were done with that project yet? Did you put a good block in it? If so its as easy as turning up the boost.Man I wish I could on mine but I still have the stock block and its living on borrowed time now.

[TurboMike]

What rpm you crossing the line at rpm wise? What is your 60ft?